Just how do you feel in regards to Installing A Bathtub?
Mounting a tub isn't specifically brain surgery, but it does require strong plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a moderately challenging job. If the old tub is conveniently easily accessible, the project can move quickly; if you have to open a wall to get rid of the old bathtub as well as place the new bath tub, the task is much harder. In either case, the project is within a house handyman's skills, although you will need an assistant to move out the old bathtub and also set in the brand-new one. Make certain you have qualified on your own for the work and also are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is much better to consider utilizing one prior to you begin. Possibilities are you may need an expert plumber to make tube links.
This post will help you set up a new bathtub in your shower room if you have currently acquired a new bathtub and also don't need to change the arrangement of your previous water supply pipes.
Your devices and also material list should make up the following:
Preparing for the Setup
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to prevent pressure on the bathtub.
Fit the adaptable tap connectors to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now be ready to be suited its final position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of removing the existing taps can be fairly bothersome because of the limited accessibility that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Before proceeding to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Making use of the two wood boards under its feet, put the bathtub in the called for position. The wood boards are useful in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 little factors.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the tub until the level checks out degree.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Turn on the water system as well as examine all joints and also new pipework for leaks as well as tighten them if required. Load the bathtub and likewise inspect the overflow outlet as well as the normal outlet for leakages.
Finally, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the bath tub has been used at least once as this will resolve it into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Safeguard the faucet in position with the supplier provided backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The previous kind must be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath meets the tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to break a rigid seal, creating the water to pass through the wall surface between the bath and also the tiling, bring about problems with wetness and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to permit the motion experienced when the tub remains in use. The sealer can break rather early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that blog entry on Installing A Bathtub while doing a lookup on the web. Sharing is nice. Helping others is fun. Kudos for your time. Kindly come visit our blog back soon.
Book Inspection
Scott Baio Then & Now!
Alfonso Ribeiro Then & Now!
Josh Saviano Then & Now!
Keshia Knight Pulliam Then & Now!
Tyra Banks Then & Now!